Login
My Garage

Ford Mondeo Recalls

There are currently 28 safety recalls out on the Ford Mondeo. To find out whether your car is affected, you'll need to find your car's VIN number.

How to find your VIN

The VIN can often be found on the lower-left corner of the dashboard, in front of the steering wheel.

You can read the number by looking through the windshield. The VIN may also appear in a number of other locations:

  • Front of the engine block. This should be easy to spot by opening the bonnet, and looking at the front of the engine.
  • Front of the car frame, near the container that holds windshield washer fluid.
  • Rear wheel well. Try looking up, directly above the tyre.
  • Inside the driver-side doorjamb. Open the door, and look underneath where the side-view mirror would be located if the door was shut.
  • Driver-side doorpost. Open the door, and look near the spot where the door latches, not too far from the seatbelt return.
  • Underneath the spare tyre.
VIN Location Diagram

If you still can't locate the VIN, try consulting your vehicle manual. Or, call a dealership or the manufacturer and request guidance.

Step 2 - See if your car is affected
  • Announcement date:
    30/10/2020
    Recalls number:
    R/2020/013
    VIN start:
    WF0FXXWPCFEA29134
    VIN end:
    WF0FXXWPCFEG42263
    Car Build Date:
    06/02/2007 - 28/02/2017
    Concern:
    Takata Air Bag Inflator May Rupture On Deployment
    Defect:
    Drivers airbag may not deploy correctly
    Remedy:
    Replace Driver air bag assembly

  • Announcement date:
    29/08/2019
    Recalls number:
    R/2019/212
    Car Build Date:
    13/02/2014 - 11/02/2019
    Concern:
    Potential Battery Acid Leakage Around Negative Terminal
    Defect:
    Possible thermal incident within the battery monitor sensor wiring
    Remedy:
    Install a fused jumper loom into the battery monitor sensor wiring

  • Announcement date:
    14/06/2019
    Recalls number:
    R/2019/020
    VIN start:
    WF0SXXGBWSCK24637
    VIN end:
    WF0EXXGBBEBD80749
    Car Build Date:
    04/08/2010 - 30/06/2014
    Concern:
    Overheating Of The Engine Cylinder Head May Cause The Cylinder Head To Crack
    Defect:
    localized overheating of the engine cylinder head may cause the cylinder head to crack.This may cause a pressurized oil leak which in extreme circumstances could result in a fire in the engine compartment.
    Remedy:
    A coolant level sensor needs to be fitted to provide an audible and visual warning to the customer and in extreme circumstances reduce the engine power.

  • Announcement date:
    22/02/2019
    Recalls number:
    R/2018/351
    VIN start:
    WF0EXXWPCEGD08045
    VIN end:
    WF0FXXWPCFJY07112
    Car Build Date:
    30/06/2016 - 30/05/2018
    Concern:
    Vehicle Could Suffer Clutch Pressure Plate Fracture
    Defect:
    A number of vehicles fitted with a 1.0 1.5 or 1.6 Ecoboost engine and 6-speed manual transmission could suffer clutch pressure plate fracture. This results in clutch smell reduced vehicle speed and performance. In the unlikely event of clutch pressure plate fracture a noise (thud / bang) could be heard from the vicinity of the transmission in extreme cases resulting in clutch / transmission fragments being released and striking under hood components creating a risk of smoke and fire from the under hood area.
    Remedy:
    To prevent the repeated heating /cooling events a new calibration has been developed for vehicles fitted with Engine Stop Start feature. The software with the additional feature sets the Instrument panel

  • Announcement date:
    19/12/2018
    Recalls number:
    R/2018/257
    Car Build Date:
    22/08/2017 - 14/12/2017
    Concern:
    The Tilt/slide Roof Opening Panel Glass S Not Correctly Bonded To Its Mounting
    Defect:
    Tilt/slide roof opening panel glass is not correctly bonded to its mounting.
    Remedy:
    Install a new roof opening glass panel on affected vehicles.

  • Announcement date:
    07/11/2018
    Recalls number:
    R/2018/213
    Car Build Date:
    01/09/2014 - 20/04/2018
    Concern:
    Possible Low Torque Condition With The Air Conditioning Clutch Fastener
    Defect:
    A/C Compressor pulley may become detached.
    Remedy:
    On affected vehicles fit a new A/C compressor clutch pulley.

  • Announcement date:
    16/07/2018
    Recalls number:
    R/2018/082
    VIN start:
    WF0EXXGBBEAG30242
    VIN end:
    WF0GXXGBBGEY27603
    Car Build Date:
    01/08/2009 - 30/06/2016
    Concern:
    Clutch Pressure Plate May Fracture
    Defect:
    Affected vehicles fitted with a 1.0 1.5 or 1.6 Ecoboost engine and 6-speed manual transmission could suffer clutch pressure plate fracture. This results in clutch smell reduced vehicle speed and performance. In the unlikely event of clutch pressure plate fracture a noise (thud / bang) could be heard from the vicinity of the transmission in extreme cases resulting in clutch / transmission fragments being released and striking under hood components creating a risk of smoke and fire from the under hood area.
    Remedy:
    To prevent the repeated heating /cooling events a new calibration has been developed for vehicles fitted with Engine Stop Start feature. The software with the additional feature sets the Instrument panel

  • Announcement date:
    16/07/2018
    Recalls number:
    R/2018/082
    VIN start:
    WF0EXXWPCEEA25812
    VIN end:
    WF0FXXWPCFGR84561
    Car Build Date:
    01/08/2009 - 30/06/2016
    Concern:
    Clutch Pressure Plate May Fracture
    Defect:
    Affected vehicles fitted with a 1.0 1.5 or 1.6 Ecoboost engine and 6-speed manual transmission could suffer clutch pressure plate fracture. This results in clutch smell reduced vehicle speed and performance. In the unlikely event of clutch pressure plate fracture a noise (thud / bang) could be heard from the vicinity of the transmission in extreme cases resulting in clutch / transmission fragments being released and striking under hood components creating a risk of smoke and fire from the under hood area.
    Remedy:
    To prevent the repeated heating /cooling events a new calibration has been developed for vehicles fitted with Engine Stop Start feature. The software with the additional feature sets the Instrument panel

  • Announcement date:
    12/03/2018
    Recalls number:
    R/2018/053
    Car Build Date:
    19/09/2014 - 28/09/2015
    Concern:
    Oil Sump May Crack Due To The Engine Overheating
    Defect:
    The engine control module calibration may not adequately detect an overheat condition in certain 2.0L Duratorq Diesel engines. In extreme cases an overheated engine can result in a breach of the oil sump leading to loss of the engine oil.
    Remedy:
    Recall the vehicles that are likely to be affected and download revised software for the control module calibration that improves overheat detection and provides an instrument cluster warning indicator to the driver and engine de-rate strategy.

  • Announcement date:
    22/02/2017
    Recalls number:
    R/2017/020
    VIN start:
    WF0DXXWPCHEB54223
    VIN end:
    WF0DXXWPCDET13815
    Car Build Date:
    05/08/2014 - 31/07/2016
    Concern:
    Seat Belt Pre-tensioner May Malfunction
    Defect:
    The driver side front seat belt pre-tensioner cable could separate during deployment leaving the driver inadequately restrained in a collision which increases the risk of injury.
    Remedy:
    Recall the vehicles that are likely to be affected and fit a new driver side front seat belt assembly.

  • Announcement date:
    20/06/2016
    Recalls number:
    R/2016/113
    VIN start:
    WF0EXXWPCEFD30710
    VIN end:
    WF0FXXWPCFFY80078
    Car Build Date:
    03/05/2014 - 22/12/2015
    Concern:
    Headlamps May Switch Off Without Warning
    Defect:
    Vehicles fitted with Adaptive LED Headlamps could experience a condition where the loss of a control signal in combination with a software error may cause the headlamps to switch off. There is a risk of collision if defect happens at night.
    Remedy:
    Recall the vehicles that are likely to be affected and updated software will be loaded to the affected modules.

  • Announcement date:
    13/09/2013
    Recalls number:
    R/2013/103
    Car Build Date:
    12/01/2012 - 11/02/2013
    Concern:
    Fire May Occur
    Defect:
    It is possible that a leak can occur between the injector spill rail connection and the plastic fuel return pipe. This can cause leakage of fuel which can either pool on the engine cylinder head and then become deposited onto the road surface where it could cause a skid risk to other motorist or if the fuel comes into contact with extremely hot engine components an exhaust manifold for instance it is possible that an under bonnet fire could ensue.
    Remedy:
    Recall all affected vehicles inspect the fuel spill rail/return pipe and if required replace the spill rail with a new modified rail.

  • Announcement date:
    18/05/2011
    Recalls number:
    R/2011/040
    Car Build Date:
    01/01/1970 - 01/01/1970
    Concern:
    Headlights And Indicators May Malfuntion
    Defect:
    Vehicles affected could demonstrate symptoms such as headlamps and indicators flashing unintentionally and/or headlamps switching off. The concern is due to software errors.
    Remedy:
    The vehicles that are likely to be affected are to be recalled to have modified software applied to the Body Control Module and Power Train Control Module.

  • Announcement date:
    21/05/2009
    Recalls number:
    R/2009/050
    Car Build Date:
    01/11/2008 - 12/03/2009
    Concern:
    Hard Brake Pedal May Occur During Engine Warm Up
    Defect:
    During engine warm up it is possible that the non return valve within the vacuum pump may stick. It is possible that if sufficient brake applications are made before the valve releases the vacuum stored within the brake booster will be used up and a hard brake pedal and longer stopping distances may result.
    Remedy:
    Recall the vehicles that are likely to be affected to fit a revised design of non return valve to the brake vacuum pump.

  • Announcement date:
    09/04/2009
    Recalls number:
    R/2009/043
    Car Build Date:
    01/01/1970 - 01/01/1970
    Concern:
    Abs May Not Function Correctly
    Defect:
    The brakes may lock up under emergency braking conditions due to valves in the hydraulic control unit being of incorrect specification.
    Remedy:
    Recall the vehicles that are likely to be affected to replace the hydraulic control unit.

  • Announcement date:
    02/08/2004
    Recalls number:
    R/2004/132
    Car Build Date:
    22/06/2004 - 09/07/2004
    Concern:
    Possible Unexpected Braking.
    Defect:
    The yaw rate sensor may be out of specification which may lead to unexpected braking
    Remedy:
    Recall affected vehicles inspect sensors and renew as necessary

  • Announcement date:
    30/04/2004
    Recalls number:
    R/2004/065
    Car Build Date:
    17/02/2004 - 11/03/2004
    Concern:
    There Is A Possibility Of Unexpected Braking.
    Defect:
    Yaw rate sensor out of specification the effect of which may result in unexpected braking
    Remedy:
    Likely to be affected vehicles will be recalled for inspection of the yaw sensors which will be replaced as necessary.

  • Announcement date:
    04/08/2003
    Recalls number:
    R/2003/083
    Car Build Date:
    01/01/1970 - 01/01/1970
    Concern:
    Modification Of Handbrake Lever
    Defect:
    The handbrake may not hold the vehicle stationary when parked if it is not applied as directed in the owner literature.
    Remedy:
    Fit a revised handbrake assembly with an improved leverage ratio.

  • Announcement date:
    03/02/2003
    Recalls number:
    R/2003/007
    Car Build Date:
    05/03/2002 - 14/11/2002
    Concern:
    Power Steering Pressure Hose May Chafe On Engine Inlet Manifold.
    Defect:
    The power steering pressure hose may chafe on the engine inlet manifold. This could ultimately result in an oil leak and a loss of power assistance to the steering.
    Remedy:
    Fit latest production level revised routing power steering pressure hose.

  • Announcement date:
    10/07/2002
    Recalls number:
    R/2002/088
    Car Build Date:
    01/06/2000 - 31/05/2002
    Concern:
    Battery Cable May Chafe And Short Circuit
    Defect:
    Battery cable may chafe on transmission valve cover plate.
    Remedy:
    Recall affected vehicles check cable insulation repair if necessary and retain cable clear of cover plate.

  • Announcement date:
    20/04/2002
    Recalls number:
    R/2002/018
    VIN start:
    Various
    Car Build Date:
    01/10/2000 - 05/07/2001
    Concern:
    Parking Brake Concern.
    Defect:
    Under certain parking conditions the vehicle handbrake may not prevent the vehicle from moving.
    Remedy:
    Ford Dealers will fit an extension block to both rear caliper handbrake actuation levers.

  • Announcement date:
    08/10/2001
    Recalls number:
    R/2001/113
    VIN start:
    XS XT XJ XU XM XP YB YR YA YG & YC
    Car Build Date:
    01/11/1999 - 01/05/2000
    Concern:
    Parking Brake Ratchet Concern
    Defect:
    The design of the parking brake ratchet teeth can allow a partial engagement resulting in damage to the tooth which can then slip to the next tooth. If ignored the wear will continue on the next tooth and the efficiency of the parking brake may become insufficient to hold the vehicle in place.
    Remedy:
    Replace parking brake lever assembly with one that has a revised tooth profile.

  • Announcement date:
    30/05/2000
    Recalls number:
    R/2000/042
    VIN start:
    Various
    Car Build Date:
    02/01/1996 - 07/08/1998
    Concern:
    Brake Fluid May Leak From Pressure Limiting Valve
    Defect:
    Corrosion of the rear brake pressure limiting valve may allow brake fluid to leak from a joint.
    Remedy:
    Recall affected vehicles and replace pressure limiting valve.

  • Announcement date:
    07/10/1999
    Recalls number:
    R/1999/084
    Car Build Date:
    03/09/1998 - 18/11/1998
    Concern:
    Door Latch Concern
    Defect:
    Some vehicles have been built with door latches which may not be to specification. An internal plastic pawl within the assembly may seize which results in the latch failing to function as designed preventing the door being securely shut.
    Remedy:
    Recall affected vehicles and fit quality assured replacement door latches.

  • Announcement date:
    09/06/1998
    Recalls number:
    R/1998/037
    Car Build Date:
    01/08/1996 - 28/02/1998
    Concern:
    Unexpected Deployment Of Passenger Air Bag
    Defect:
    Unexpected passenger air bag deployment due to an electrostatic discharge through the air bag igniter.
    Remedy:
    Recall affected vehicles and fit ground wire to passenger air bag

  • Announcement date:
    15/03/1996
    Recalls number:
    R/1996/040
    VIN start:
    SU
    Car Build Date:
    10/10/1995 - 12/10/1995
    Concern:
    Possible Failure Of Offside Front Brake Caliper
    Defect:
    It is possible that some Mondeo vehicles may have been fitted with a right hand front brake caliper where the casting is not to specification. In time this may result in fluid leakage with the loss of one brake circuit.
    Remedy:
    Recall the affected vehicles for a check on the manufacturing date of the subject caliper. Caliper units falling within the affected range will be replaced.

  • Announcement date:
    23/01/1996
    Recalls number:
    R/1996/022
    Car Build Date:
    19/06/1995 - 01/01/1970
    Concern:
    Failure Of Braking System Vacuum Assistance
    Defect:
    The brake vacuum pump may cease to provide vacuum assistance. Should this occur greater brake pedal pressure would be needed and stopping distances may be increased.
    Remedy:
    The affected vehicles are being recalled to Ford dealers to have the brake pump manufacturing codes checked. Vacuum pumps within certain ranges will be replaced with new units. This campaign supersedes recall R1995/081 and includes all the vehicles alrea

  • Announcement date:
    26/09/1994
    Recalls number:
    R/1994/038
    VIN start:
    1992 - NY NS NT
    Car Build Date:
    01/10/1992 - 14/07/1993
    Concern:
    Failure Of Headlamps
    Defect:
    A possibility exists that excessive torque generated when turning on the headlamp switch may induce an internal open circuit and cause the headlamps to go out.
    Remedy:
    Recall the affected vehicles for replacement of the headlamp switch with a revised component.
Step 3 - Contact your nearest dealer

Enter your postcode to see your nearest franchised dealer: