Login
My Garage
  1. Home
  2. Recalls
  3. Toyota Aygo

Toyota Aygo Recalls

There are currently 13 safety recalls out on the Toyota Aygo. To find out whether your car is affected, you'll need to find your car's VIN number.

How to find your VIN

The VIN can often be found on the lower-left corner of the dashboard, in front of the steering wheel.

You can read the number by looking through the windshield. The VIN may also appear in a number of other locations:

  • Front of the engine block. This should be easy to spot by opening the bonnet, and looking at the front of the engine.
  • Front of the car frame, near the container that holds windshield washer fluid.
  • Rear wheel well. Try looking up, directly above the tyre.
  • Inside the driver-side doorjamb. Open the door, and look underneath where the side-view mirror would be located if the door was shut.
  • Driver-side doorpost. Open the door, and look near the spot where the door latches, not too far from the seatbelt return.
  • Underneath the spare tyre.
VIN Location Diagram

If you still can't locate the VIN, try consulting your vehicle manual. Or, call a dealership or the manufacturer and request guidance.

Step 2 - See if your car is affected
  • Announcement date:
    25/01/2021
    Recalls number:
    R/2020/351
    VIN start:
    *********0N569303
    VIN end:
    *********0N577522
    Car Build Date:
    27/08/2020 - 08/10/2020
    Concern:
    Some Rear Inner Seat Belts May Have Incorrect Stitching On The Belt Material
    Defect:
    On affected vehicles some rear inner seat belts may have incorrect stitching on the belt material.
    Remedy:
    Check seat belts and relace if necessary.
  • Announcement date:
    20/10/2020
    Recalls number:
    R/2020/254
    VIN start:
    0N548056-0N551074
    VIN end:
    0N547996-0N551192
    Car Build Date:
    03/06/2020 - 15/06/2020
    Concern:
    It May Not Be Possible To Switch Headlights From High Beam To Low Beam Or Low Beam To High Beam
    Defect:
    It may not be possible to switch headlights from high beam to low beam or low beam to high beam.
    Remedy:
    Replace the Headlamp Units
  • Announcement date:
    21/01/2019
    Recalls number:
    R/2018/315
    VIN start:
    0N002025-0N016750
    VIN end:
    0N002061-0N716088
    Car Build Date:
    17/02/2005 - 19/12/2013
    Concern:
    There Is A Possibility That The Glue Holding The Glass On The Rear Door Could Detach
    Defect:
    There is a possibility that the glue holding the glass on the rear door could detach.
    Remedy:
    Inspect and repair or replace the rear window glass if necessary.
  • Announcement date:
    21/01/2019
    Recalls number:
    R/2018/316
    VIN start:
    JTDKGNECX0N068880
    VIN end:
    JTDKGNECX0N068880
    Car Build Date:
    23/02/2015 - 23/02/2015
    Concern:
    An Incorrect Tooling Setup During The Manufacturing Of The Fuel Tank May Result In Reduced Wall Thickness Or Small Pin Hole In The Tank's Bottom Surface
    Defect:
    An incorrect tooling setup during the manufacturing of the fuel tank may result in reduced wall thickness
    Remedy:
    Check the serial number and replace the fuel tank if necessary.
  • Announcement date:
    21/01/2019
    Recalls number:
    R/2018/316
    VIN start:
    JTDKGNEC00N192821
    VIN end:
    JTDKGNEC00N192821
    Car Build Date:
    30/06/2016 - 30/06/2016
    Concern:
    An Incorrect Tooling Setup During The Manufacturing Of The Fuel Tank May Result In Reduced Wall Thickness Or Small Pin Hole In The Tank's Bottom Surface
    Defect:
    An incorrect tooling setup during the manufacturing of the fuel tank may result in reduced wall thickness
    Remedy:
    Check the serial number and replace the fuel tank if necessary.
  • Announcement date:
    21/01/2019
    Recalls number:
    R/2018/316
    VIN start:
    JTDKG18CX0N574763
    VIN end:
    JTDKG18CX0N574763
    Car Build Date:
    26/08/2011 - 26/08/2011
    Concern:
    An Incorrect Tooling Setup During The Manufacturing Of The Fuel Tank May Result In Reduced Wall Thickness Or Small Pin Hole In The Tank's Bottom Surface
    Defect:
    An incorrect tooling setup during the manufacturing of the fuel tank may result in reduced wall thickness
    Remedy:
    Check the serial number and replace the fuel tank if necessary.
  • Announcement date:
    29/06/2016
    Recalls number:
    R/2016/149
    VIN start:
    JTDJGNEC#0N022080
    VIN end:
    JTDKPNEC#0N002102
    Car Build Date:
    09/09/2014 - 15/10/2014
    Concern:
    Steering Column May Fail Unexpectedly
    Defect:
    A component of the steering column may not be to specification and could fail. If this occurs there would be a loss of directional control.
    Remedy:
    The manufacturer will contact keepers of affected vehicles and advise not to use the vehicle. Examine vehicles and on those with the affected component replace the steering column.
  • Announcement date:
    28/01/2015
    Recalls number:
    R/2014/172
    VIN start:
    JTDJG1#C#N714295
    VIN end:
    JTDJG1#C#N726316
    Car Build Date:
    20/06/2013 - 27/08/2013
    Concern:
    Loss Of Control
    Defect:
    The front shock absorber rod may have an internal fault which could cause it to break. This could have an adverse affect on the front suspension and the driver's ability to control the vehicle.
    Remedy:
    On affected vehicles replace both front shock absorbers.
  • Announcement date:
    28/01/2015
    Recalls number:
    R/2014/172
    VIN start:
    JTDKG1#C#N714236
    VIN end:
    JTDKG1#C#N726320
    Car Build Date:
    20/06/2013 - 27/08/2013
    Concern:
    Loss Of Control
    Defect:
    The front shock absorber rod may have an internal fault which could cause it to break. This could have an adverse affect on the front suspension and the driver's ability to control the vehicle.
    Remedy:
    On affected vehicles replace both front shock absorbers.
  • Announcement date:
    03/03/2014
    Recalls number:
    R/2014/020
    VIN start:
    JTDJG10C#0N721662
    VIN end:
    JTDJG10C#0N723223
    Car Build Date:
    26/07/2013 - 21/08/2013
    Concern:
    Directional Control May Be Lost
    Defect:
    On subject vehicles there is a possibility that a wld on the rear axle may not be sufficient. In the worst case scenarios this could cause a break in connection between rear axle and the body. This could cause difficulty in controlling the vehicle.
    Remedy:
    Owners of subject vehicles to be contacted by first class post (using DVLA records). Inspect subject vehicles and if fault found replace rear axle.
  • Announcement date:
    03/03/2014
    Recalls number:
    R/2014/020
    VIN start:
    JTDJG18C#0N723058
    VIN end:
    JTDJG18C#0N723058
    Car Build Date:
    31/08/2013 - 31/07/2013
    Concern:
    Directional Control May Be Lost
    Defect:
    On subject vehicles there is a possibility that a wld on the rear axle may not be sufficient. In the worst case scenarios this could cause a break in connection between rear axle and the body. This could cause difficulty in controlling the vehicle.
    Remedy:
    Owners of subject vehicles to be contacted by first class post (using DVLA records). Inspect subject vehicles and if fault found replace rear axle.
  • Announcement date:
    03/03/2014
    Recalls number:
    R/2014/020
    VIN start:
    JTDKG10C#0N721546
    VIN end:
    JTDKG10C#0N723228
    Car Build Date:
    26/07/2013 - 20/08/2013
    Concern:
    Directional Control May Be Lost
    Defect:
    On subject vehicles there is a possibility that a wld on the rear axle may not be sufficient. In the worst case scenarios this could cause a break in connection between rear axle and the body. This could cause difficulty in controlling the vehicle.
    Remedy:
    Owners of subject vehicles to be contacted by first class post (using DVLA records). Inspect subject vehicles and if fault found replace rear axle.
  • Announcement date:
    06/02/2010
    Recalls number:
    R/2010/010
    Car Build Date:
    01/02/2005 - 31/08/2009
    Concern:
    Accelerator Pedal May Fail To Return To Idle
    Defect:
    It has been identified that on affected vehicles condensation resulting from cold-weather use of the heater or other causes may form on the worn surface of a component within the throttle pedal assembly known as the friction device. If this occurs there is a possibility that in the worst case the accelerator pedal may return slowly or does not return to the engine idle position.
    Remedy:
    Recalled vehicles will have a precision-cut steel reinforcing bar fitted into the accelerator pedal assembly which will create a space in order to reduce the surface tension between the friction device and a component referred to as the pedal arm. The subject bar also strengthens the reaction force of the spring that returns the accelerator pedal to it's non-pressed position.
Step 3 - Contact your nearest dealer

Enter your postcode to see your nearest franchised dealer: