Login
My Garage
  1. Home
  2. Recalls
  3. Iveco Stralis

Iveco Stralis Recalls

There are currently 28 safety recalls out on the Iveco Stralis. To find out whether your car is affected, you'll need to find your car's VIN number.

How to find your VIN

The VIN can often be found on the lower-left corner of the dashboard, in front of the steering wheel.

You can read the number by looking through the windshield. The VIN may also appear in a number of other locations:

  • Front of the engine block. This should be easy to spot by opening the bonnet, and looking at the front of the engine.
  • Front of the car frame, near the container that holds windshield washer fluid.
  • Rear wheel well. Try looking up, directly above the tyre.
  • Inside the driver-side doorjamb. Open the door, and look underneath where the side-view mirror would be located if the door was shut.
  • Driver-side doorpost. Open the door, and look near the spot where the door latches, not too far from the seatbelt return.
  • Underneath the spare tyre.
VIN Location Diagram

If you still can't locate the VIN, try consulting your vehicle manual. Or, call a dealership or the manufacturer and request guidance.

Step 2 - See if your car is affected
  • Announcement date:
    11/11/2022
    Recalls number:
    R/2022/333
    Car Build Date:
    01/10/2018 - 30/09/2022
    Concern:
    The Front Axle Leave Spring Retainers (u-bolts) Could Work Loose Or May Be Lost During A Driving Cycle.
    Defect:
    The Front axle leave spring retainers (U-Bolts) could work loose or may be lost during a driving cycle.
    Remedy:
    Retighten front axle U-Bolt with an increased torque
  • Announcement date:
    01/05/2021
    Recalls number:
    R/2021/424
    VIN start:
    WJMM62AVZ0C443611
    VIN end:
    JMM62AU90C448195
    Car Build Date:
    01/12/2020 - 31/03/2021
    Concern:
    Possible Lack Of Cotter Pin Or Wrong Cotter Pin Assembly On Steering Axle
    Defect:
    Possible incorrect or missing cotter pin on steered axle joint.
    Remedy:
    Check and re-torque the nut and replacement of the cotter pin on the steering rod.
  • Announcement date:
    14/02/2017
    Recalls number:
    R/2016/285
    Car Build Date:
    01/09/2015 - 23/08/2016
    Concern:
    Brakes May Not Perform As Intended
    Defect:
    It has been identified that the Central Brake Unit and Rear Axle Modulator units may not function as intended. This can cause a higher braking retardation or quicker braking than anticipated. This can result in the vehicle stopping quicker that expected.
    Remedy:
    Recall all affected vehicles to check the production dates of the Central Brake Unit and Rear Axle Modulator units and change the units if found to be within the affected production range.
  • Announcement date:
    21/05/2013
    Recalls number:
    R/2013/065
    Car Build Date:
    01/01/1970 - 01/01/1970
    Concern:
    Steering Bolts May Foul Other Components
    Defect:
    It has been identified that the swivel head on the hydraulic operating cylinder for the second steer axle may not have been installed to IVECO's specification. This can cause fouling of other components which may affect the directional control of the vehicle.
    Remedy:
    Recall all affected vehicles to check and if required reposition the hydraulic operating cylinder swivel head.
  • Announcement date:
    24/01/2013
    Recalls number:
    R/2013/011
    VIN start:
    WJME2N5H404383581
    VIN end:
    WJME2NWH404387566
    Car Build Date:
    01/01/1970 - 01/01/1970
    Concern:
    Braking Efficiency May Be Compromised
    Defect:
    Due to continuous quality control it has shown on a limited number of vehicles it may be necessary to replace a component of the brake valve EBS2 in order to ensure perfect efficiency of the braking system.Failure to replace the component described could compromise the correct operation of the braking system.
    Remedy:
    Replacement of the relay piston / sealing ring on the brake value of the EBS2 (CBU) tractor.
  • Announcement date:
    24/01/2013
    Recalls number:
    R/2013/012
    VIN start:
    WJMM1VUH40C260575
    VIN end:
    WJMM1VTH40C255768
    Car Build Date:
    01/01/1970 - 01/01/1970
    Concern:
    A Frame Retaining Screws May Be Incorrectly Torqued
    Defect:
    On a number of vehicles the torque setting value of the retaining screws of the A frame guide rod joint to the axle could be wrong.
    Remedy:
    Checks to be carried out to ensure that the correct torque is applied.
  • Announcement date:
    15/03/2012
    Recalls number:
    R/2012/034
    VIN start:
    Not yet known
    VIN end:
    TBA
    Car Build Date:
    01/01/1970 - 01/01/1970
    Concern:
    Pneumatic Suspension Could Fail
    Defect:
    On-going product and quality checks have shown that there may be defects in the Air suspension supports.
    Remedy:
    Check the supports for the air bellow manufacturing and casting numbers and replace i required.
  • Announcement date:
    15/03/2012
    Recalls number:
    R/2012/034
    VIN start:
    WJMA1VNH404382365
    VIN end:
    WJMS2NUH404384833
    Car Build Date:
    01/01/1970 - 01/01/1970
    Concern:
    Pneumatic Suspension Could Fail
    Defect:
    On-going product and quality checks have shown that there may be defects in the Air suspension supports.
    Remedy:
    Check the supports for the air bellow manufacturing and casting numbers and replace i required.
  • Announcement date:
    11/10/2010
    Recalls number:
    R/2010/162
    Car Build Date:
    01/01/1970 - 01/01/1970
    Concern:
    Steering Control Could Be Lost
    Defect:
    The second axle steering ram and/or clevis assembly may not be to specification which will result in some movement between the mounting and the ram. If ignored the movement will increase with usage and could eventually lead to separation of the ram and mounting resulting in the steering control being impaired.
    Remedy:
    Recall the vehicles that are likely to be affected to check and where necessary replace parts as indicated by the repair procedure issued by the manufacturer.
  • Announcement date:
    15/12/2008
    Recalls number:
    R/2008/195
    VIN start:
    WJMM1VPH404360524
    VIN end:
    WJMM1VPH404363471
    Car Build Date:
    01/07/2008 - 30/09/2008
    Concern:
    Fifth Wheel Base May Fracture
    Defect:
    Under extreme conditions the fifth wheel bed plate may flex and damage the fifth wheel base.
    Remedy:
    Recall affected vehicles replace the fifth wheel and bed plate if manufactured by GF
  • Announcement date:
    10/03/2008
    Recalls number:
    R/2008/016
    VIN start:
    WJMM1VSH404323570
    VIN end:
    WJMM1VTH404325861
    Car Build Date:
    01/12/2006 - 31/01/2007
    Concern:
    Risk Of Instability
    Defect:
    It is possible that the material used for the rear anti roll bar supports may be incorrect and could collapse causing serious stability concerns.
    Remedy:
    Recall the vehicles that are likely to be affected to replace both the rear anti roll bar supports.
  • Announcement date:
    10/03/2008
    Recalls number:
    R/2008/016
    VIN start:
    WJMB1VNS40C174630
    VIN end:
    WJME2NTH40C178656
    Car Build Date:
    01/12/2006 - 31/01/2007
    Concern:
    Risk Of Instability
    Defect:
    It is possible that the material used for the rear anti roll bar supports may be incorrect and could collapse causing serious stability concerns.
    Remedy:
    Recall the vehicles that are likely to be affected to replace both the rear anti roll bar supports.
  • Announcement date:
    14/08/2007
    Recalls number:
    R/2007/104
    VIN start:
    WJMA1VM100C157524
    VIN end:
    WJMA1VNH40C180361
    Car Build Date:
    01/11/2005 - 31/01/2007
    Concern:
    Exhaust Silencer Retaining Bolts May Fail
    Defect:
    It is possible for the for the exhaust silencer strap bolts to slacken which if not rectified could lead to the total failure of the silencer mounting.
    Remedy:
    Recall the vehicles that are likely to be affected to replace the mounting bolts with new pre-coated bolts (locking compound) and tighten to the correct torque.
  • Announcement date:
    14/08/2007
    Recalls number:
    R/2007/104
    VIN start:
    WJMM1VSH404306677
    VIN end:
    `WJMM1VTH404325414
    Car Build Date:
    01/11/2005 - 31/12/2006
    Concern:
    Exhaust Silencer Retaining Bolts May Fail
    Defect:
    It is possible for the for the exhaust silencer strap bolts to slacken which if not rectified could lead to the total failure of the silencer mounting.
    Remedy:
    Recall the vehicles that are likely to be affected to replace the mounting bolts with new pre-coated bolts (locking compound) and tighten to the correct torque.
  • Announcement date:
    02/08/2007
    Recalls number:
    R/2007/090
    VIN start:
    WJMA1VUJ004278496
    VIN end:
    WJMA1VM0004290942
    Car Build Date:
    06/04/2004 - 10/12/2004
    Concern:
    Loss Of Steering
    Defect:
    Steering control could be lost on vehicles that have been fitted with non-quality assured steering column shafts.
    Remedy:
    Recall the vehicles that are likely to be affected to check and if necessary replace the steering column shaft.
  • Announcement date:
    02/08/2007
    Recalls number:
    R/2007/090
    VIN start:
    WJMM1VRP00C126284
    VIN end:
    WJMJ4CSS00C143500
    Car Build Date:
    06/10/2003 - 15/11/2004
    Concern:
    Loss Of Steering
    Defect:
    Steering control could be lost on vehicles that have been fitted with non-quality assured steering column shafts.
    Remedy:
    Recall the vehicles that are likely to be affected to check and if necessary replace the steering column shaft.
  • Announcement date:
    31/01/2007
    Recalls number:
    R/2006/216
    VIN start:
    WJMS2NUH004314789
    VIN end:
    WJMS2NUH043211554
    Car Build Date:
    01/05/2006 - 01/10/2006
    Concern:
    Cab May Shudder Under Extreme Operating Conditions
    Defect:
    Possibility that front Cab mounting bolts may be missing resulting in that Cab may shudder under extreme operating conditions.
    Remedy:
    Recall affected vehicles and fit new Cab mounting bolts
  • Announcement date:
    27/03/2006
    Recalls number:
    R/2006/020
    VIN start:
    WJME2NSJ004285721
    VIN end:
    WJMS2NSK004288902
    Car Build Date:
    01/09/2004 - 30/11/2004
    Concern:
    Cab Side Member May Deform
    Defect:
    It has been identified that the cab lower side member may become deformed due to excessive hydraulic tilt pump pressure.
    Remedy:
    Recalled vehicles will have the cab tilt pump pressure reduced to 310 bar. Should the cab side member be deformed a repair to rectify this will be carried out.
  • Announcement date:
    07/02/2006
    Recalls number:
    R/2005/184
    VIN start:
    WJMS2NSK004292511
    VIN end:
    WJMS2NUH004301183
    Car Build Date:
    27/01/2005 - 14/07/2005
    Concern:
    Propshaft May Contact Axle Beam
    Defect:
    Under certain circumstances it is possible that the distance between the propshaft and the second front axle may be insufficient. Should axle/propshaft contact be made damage to one or both of these components might ensue.
    Remedy:
    Recalled vehicles will have the clearance between the propshaft and the second front axle beam checked. Should the clearance be outside of the specified parameters the suspension will be adjusted.
  • Announcement date:
    16/06/2005
    Recalls number:
    R/2005/067
    VIN start:
    WJME2NSJ004286634
    VIN end:
    WJMM1VUJ004291516
    Car Build Date:
    13/10/2004 - 27/12/2004
    Concern:
    Track And Drop Arm Retaining Bolts May Be Incorrectly Tightened
    Defect:
    The retaining bolts of the drop arm and track arms may not have been tightened to the correct torque. With the possibility that the bolts may become loose.
    Remedy:
    Recalled vehicles will have the subject bolts tightened to the correct torque.
  • Announcement date:
    11/04/2005
    Recalls number:
    R/2005/007
    VIN start:
    WJMS2NSK004266447
    VIN end:
    WJME2NP0004287471
    Car Build Date:
    25/04/2003 - 10/10/2004
    Concern:
    Possibility That The Cab Tilting Cylinder Bracket May Deform
    Defect:
    The possibility exists that the bracket which carries the cab tilt cylinder may deform. This can lead to unforeseen dropping of the cab when in the tilted position.
    Remedy:
    Recalled vehicles will have the relevant bracket inspected and repaired/modified as dictated by the Iveco Market Help Desk. In all cases the lift mechanism hydraulic pressure will be reduced from 370 to 310 bar.
  • Announcement date:
    07/09/2004
    Recalls number:
    R/2004/138
    VIN start:
    WJMM1USK004189298
    VIN end:
    WJMM1VUJ004265949
    Car Build Date:
    01/05/1997 - 28/02/2003
    Concern:
    Contaminated Air May Be Drawn Into Intake System
    Defect:
    There is a possibility that contaminated air may be drawn into the engine air intake system (eg Cigarette ends)
    Remedy:
    Recall affected vehicles and fit a protective grille over air intake pipe.
  • Announcement date:
    07/09/2004
    Recalls number:
    R/2004/137
    VIN start:
    WJMS2NSK004266447
    VIN end:
    WJMS2NSK004270834
    Car Build Date:
    01/05/2003 - 31/07/2003
    Concern:
    Positive Alternator Cable May Rub On Chassis Side Cross Member.
    Defect:
    There is a possibility that the positive alternator cable may rub/chaff on chassis side member
    Remedy:
    Recall affected vehicles replace bracket and clamps and adjust positive cable routing on chassis.
  • Announcement date:
    04/05/2004
    Recalls number:
    R/2004/058
    VIN start:
    WJME2NRK004268921
    VIN end:
    WJME2NSJ004273495
    Car Build Date:
    07/05/2003 - 29/09/2003
    Concern:
    Possibility That Antiroll Bar Does Not Comply With Matierial Requirements
    Defect:
    The Antiroll Bar may not comply with material requirements
    Remedy:
    Recall affected vehicles and on those with manufacturing dates of 03-21/03 - 25/03-35 replace bar.
  • Announcement date:
    01/05/2003
    Recalls number:
    R/2003/040
    VIN start:
    WJM99999904240022 WJME2NP000C083924
    VIN end:
    WJME2NRK004263253 WJME2NUH00C115161
    Car Build Date:
    01/10/2000 - 31/12/2002
    Concern:
    Breakage Of External Sun Visor
    Defect:
    Due to faults in the shape and dimensions of the sun visor during production tensions can occur following fitting to the cab and can cause the visor to break.
    Remedy:
    Modify the sun visor mountings by using a new tension free mounting bracket.
  • Announcement date:
    01/05/2003
    Recalls number:
    R/2003/031
    VIN start:
    WJM99999904240022
    VIN end:
    WJMM1VSK004258488
    Car Build Date:
    01/01/1970 - 01/01/1970
    Concern:
    Possible Water Ingress Into Cab Tilt Relay Box
    Defect:
    Ingress of water into the cab tilt relay box may corrode the electrical connections and impair the effectiveness of the tilt locking system.
    Remedy:
    Move the relay box from the bottom flange of the chassis to the inside of the chassis frame.
  • Announcement date:
    01/05/2003
    Recalls number:
    R/2003/031
    VIN start:
    WJMM1VUJ00C083429
    VIN end:
    WJMM1VUJ00C109825
    Car Build Date:
    01/01/1970 - 01/01/1970
    Concern:
    Possible Water Ingress Into Cab Tilt Relay Box
    Defect:
    Ingress of water into the cab tilt relay box may corrode the electrical connections and impair the effectiveness of the tilt locking system.
    Remedy:
    Move the relay box from the bottom flange of the chassis to the inside of the chassis frame.
  • Announcement date:
    27/01/2003
    Recalls number:
    R/2003/154
    Car Build Date:
    17/04/1998 - 27/06/2002
    Concern:
    Possibile Air Loss From Brake System
    Defect:
    There is the possibility of an air loss from the footbrake system due to corrosion in the pressure regulator APU valve (air dryer with four circuit safety valve].
    Remedy:
    To prevent corrosion in the pressure regulator APU a new rubber diaphragm will be fitted.
Step 3 - Contact your nearest dealer

Enter your postcode to see your nearest franchised dealer: