Login
My Garage

Land Rover Range Rover Recalls

There are currently 67 safety recalls out on the Land Rover Range Rover. To find out whether your car is affected, you'll need to find your car's VIN number.

How to find your VIN

The VIN can often be found on the lower-left corner of the dashboard, in front of the steering wheel.

You can read the number by looking through the windshield. The VIN may also appear in a number of other locations:

  • Front of the engine block. This should be easy to spot by opening the bonnet, and looking at the front of the engine.
  • Front of the car frame, near the container that holds windshield washer fluid.
  • Rear wheel well. Try looking up, directly above the tyre.
  • Inside the driver-side doorjamb. Open the door, and look underneath where the side-view mirror would be located if the door was shut.
  • Driver-side doorpost. Open the door, and look near the spot where the door latches, not too far from the seatbelt return.
  • Underneath the spare tyre.
VIN Location Diagram

If you still can't locate the VIN, try consulting your vehicle manual. Or, call a dealership or the manufacturer and request guidance.

Step 2 - See if your car is affected
  • Announcement date:
    26/06/2026
    Recalls number:
    R/2026/241
    Car Build Date:
    03/01/2024 - 06/12/2024
    Concern:
    Aj20-d6 Idler Pulley Clash
    Defect:
    A concern has been identified on certain AJ20-D6 engines where the Front End Auxiliary Drive (FEAD) belt idler pulley may over-rotate following a high torsion input and lead to a clash with and damage to the oil pressure and temperature sensor. A damaged oil pressure and temperature sensor can lead to an oil leak from the engine which can result in a slip hazard for following road users particularly two-wheeled vehicles.
    Remedy:
    Vehicles will have the Front-End Auxiliary Drive (FEAD) idler pulley replaced.
  • Announcement date:
    19/06/2026
    Recalls number:
    R/2026/245
    Car Build Date:
    25/09/2020 - 04/06/2026
    Concern:
    Driver’s Airbag Potential Non-deployment
    Defect:
    A concern has been identified where the connector to the driver’s airbag at the clockspring may experience fretting corrosion over time. This can lead to an increased resistance in the driver’s airbag circuit potentially resulting in the airbag failing to deploy when requested to do so. An airbag which fails to deploy as-intended will increase the risk of injury in the event of a crash.
    Remedy:
    Vehicles will have a protective lubricant gel applied to the driver’s airbag connector terminals.
  • Announcement date:
    27/05/2026
    Recalls number:
    R/2026/198
    Car Build Date:
    17/02/2026 - 27/02/2026
    Concern:
    Range Rover Range Rover Sport And Range Rover Velar Audio Amplifier Water Damage
    Defect:
    A concern has been identified on certain 2026 model year Range Rover Range Rover Sport and Range Rover Velar vehicles where the audio amplifiers may have been subject to water damage and may not provide any audio output including no seat belt reminder audible warnings to the driver. A seat belt reminder audible warning chime that does not alert of an unlatched seat belt can increase the risk of occupant injury in the event of a crash.
    Remedy:
    Affected vehicles will have the audio amplifier replaced.
  • Announcement date:
    21/05/2026
    Recalls number:
    R/2026/079
    Car Build Date:
    12/08/2021 - 12/10/2025
    Concern:
    Range Rover And Range Rover Sport Panoramic Roof Side Finisher Loose
    Defect:
    The manufacturer has identified a concern on certain Range Rover and Range Rover Sport vehicles where the adhesion process used to re-attach the panoramic roof side finishers during vehicle quality rework operations in the assembly plant may not have been sufficient. An inadequately adhered panoramic roof side finisher could over time come partially or completely loose. This could result in distraction to the driver or other road users or in the event of complete detachment harm to other road users particularly pedestrians or two-wheeled vehicles and increase the risk of injury or a crash.
    Remedy:
    Vehicles will have the panoramic roof side finisher removed and securely attached.
  • Announcement date:
    28/04/2026
    Recalls number:
    R/2026/078
    Car Build Date:
    26/01/2023 - 05/01/2025
    Concern:
    Range Rover And Range Rover Sport Plug-in Hybrid Battery Capacity
    Defect:
    The manufacturer has identified a concern on certain Range Rover and Range Rover Sport plug-in hybrid vehicles where due to inadequate penetration of welding between the cells the battery’s capacity and therefore the vehicle’s electric range may be depleted below the design intent condition. A below-specification electric range will not meet the as-certified value for the vehicle and is therefore non-compliant to emissions legislation.
    Remedy:
    Vehicles will have the hybrid battery/modules replaced.
  • Announcement date:
    11/02/2026
    Recalls number:
    R/2025/491
    Car Build Date:
    24/07/2018 - 11/09/2018
    Concern:
    Range Rover And Range Rover Sport Samsung Phev Battery Cell Degradation
    Defect:
    A concern has been identified on certain Range Rover & Range Rover Sport PHEV (Plug-in Hybrid Electric Vehicle) vehicles containing high-voltage batteries with cells manufactured between 11th and 12th April 2018. Cathode damage introduced during the cell folding process can lead to high time-in-service cell degradation.
    Remedy:
    Data will be extracted from vehicles then the high voltage traction battery pack will be replaced.
  • Announcement date:
    30/10/2025
    Recalls number:
    R/2025/436
    Car Build Date:
    19/08/2025 - 29/08/2025
    Concern:
    Gear Shift Module Moisture Ingress
    Defect:
    On Affected vehicles it is possible that moisture has entered the Gear Shift Module (GSM) during the assembly process. Under certain conditions there is a risk that this moisture could result in non-illumination of the Light Emitting Diode (LED) indicating the selected gear. Non-illumination of the LED gear indicator adjacent to the shifter would not conform to regulated requirements for automatic transmission control position indicator illumination.
    Remedy:
    Affected vehicles will have the Gear Shift Module replaced.
  • Announcement date:
    06/08/2025
    Recalls number:
    R/2025/302
    Car Build Date:
    08/10/2014 - 26/03/2015
    Concern:
    Range Rover (l405) Front Suspension Knuckle Crack – Incorrect Repair
    Defect:
    The manufacturer identified that on a small number of vehicles the JLR N759 safety recall repair procedure had not been carried out correctly. The suspension knuckles had not been replaced in all cases where the repair instruction directed a replacement leaving the defect present on the vehicles.
    Remedy:
    Both front suspension knuckles will be inspected for the presence of any cracks. Where no crack is present and where available a retaining bracket will be fitted to the joint. Where cracks are found or a bracket is not available the front suspension knuckle will be replaced.
  • Announcement date:
    09/05/2025
    Recalls number:
    R/2025/149
    Car Build Date:
    17/01/2013 - 19/06/2015
    Concern:
    Security Guidance
    Defect:
    Jaguar Land Rover in conjunction with law enforcement and insurance bodies is aware of the increase in thefts of vehicles in specific geographical locations within the United Kingdom. there is no fault with Jaguar Land Rover's security systems and they continue to meet stringent automotive legislation. Jaguar Land Rover is offering owners guidance on how to maximise vehicle security and protect against theft.
    Remedy:
    Vehicle registered keepers will be sent a security guidance letter only - there is no repair action.
  • Announcement date:
    11/03/2025
    Recalls number:
    R/2025/102
    Car Build Date:
    19/12/2024 - 19/02/2025
    Concern:
    Range Rover And Range Rover Sport Second Row Centre Seat Belt Buckle Cable Misaligned
    Defect:
    On affected vehicles the second-row centre seat belt buckle may have been manufactured incorrectly. An internal obstruction to the seat belt tongue can prevent correct latching. In the event of a crash an insecurely latched seat belt buckle could increase the risk of personal injury.
    Remedy:
    Vehicles will have the centre seat belt buckle and buckle retaining bolt replaced.
  • Announcement date:
    27/01/2025
    Recalls number:
    R/2024/146
    Car Build Date:
    02/02/2015 - 06/11/2017
    Concern:
    Security Enhancement
    Defect:
    For affected vehicles the manufacturer has developed a software enhancement to further increase vehicle security.
    Remedy:
    The software enhancement will deploy this update and reduce the theft risk.
  • Announcement date:
    20/11/2024
    Recalls number:
    R/2024/435
    Car Build Date:
    28/06/2024 - 01/07/2024
    Concern:
    48v Harness Clash With Cross Brace
    Defect:
    On affected vehicles the 48V cable could become too close to an underbody cross-brace and rub against the metal cross-brace exposing the cable core resulting in a short circuit and risk of fire.
    Remedy:
    Inspect harness and as needed reposition the routing bracket as necessary.
  • Announcement date:
    19/07/2024
    Recalls number:
    R/2024/227
    Car Build Date:
    06/09/2023 - 01/12/2023
    Concern:
    2024 Model Year Range Rover And Range Rover Sport Loss Of Drive
    Defect:
    For affected vehicles the clutch plates within the hybrid transmission may have been manufactured with a flatness out of tolerance to the engineering specification.
    Remedy:
    Diagnostic test to determine whether the clutch packs within the transmission are operating as expected. Any transmissions which fail the test will be replaced.
  • Announcement date:
    14/06/2024
    Recalls number:
    R/2024/255
    Car Build Date:
    14/04/2021 - 05/03/2024
    Concern:
    Aj20-d6 And Aj20-p6 Engine Oil Filter Housing Cracked
    Defect:
    On affected vehicles the incorrect specification of plastic was used to manufacture the oil filter housing. This housing may over time and with vehicle use crack. This could result in oil under pressure leaking and coming into contact with hot components of the engine which may result in a fire. Additionally oil may leak onto the road surface posing a skid hazard.
    Remedy:
    Replace the oil filter housing complete with filter and associated O-rings.
  • Announcement date:
    25/04/2024
    Recalls number:
    R/2024/167
    Car Build Date:
    11/01/2024 - 18/01/2024
    Concern:
    Phev Traction Battery Busbar Weld Penetration
    Defect:
    For the affected vehicle a concern has been identified where the there is an inadequate depth of weld (penetration) between the busbar and the anode in the module of the Plug-in Hybrid Electric Vehicle (PHEV) battery.
    Remedy:
    Replacement of the traction battery.
  • Announcement date:
    27/03/2024
    Recalls number:
    R/2024/100
    Car Build Date:
    24/11/2023 - 24/11/2023
    Concern:
    Aj20-d6 Fuel Injector Clamp Cracked
    Defect:
    A concern has been identified where the clamps used to secure the fuel injectors into the cylinder head on certain AJ20-D6 engines may crack allowing the injector to come loose. This loose injector could become unseated allowing fuel to be pushed past the injector seal from the combustion chamber or the fuel feed system.
    Remedy:
    A fuel leak in this area could result in fuel spill onto hot engine components which may result in a fire.
  • Announcement date:
    15/03/2024
    Recalls number:
    R/2024/145
    Car Build Date:
    02/11/2020 - 04/05/2022
    Concern:
    Security Enhancement
    Defect:
    For affected vehicles the manufacturer has developed a software enhancement to further increase vehicle security.
    Remedy:
    The software enhancement will deploy this update and reduce the theft risk.
  • Announcement date:
    14/03/2024
    Recalls number:
    R/2024/147
    Car Build Date:
    25/09/2020 - 26/02/2024
    Concern:
    Security Enhancement
    Defect:
    For affected vehicles the manufacturer has developed a software enhancement to further increase vehicle security.
    Remedy:
    The software enhancement will deploy this update and reduce the theft risk.
  • Announcement date:
    08/01/2024
    Recalls number:
    R/2023/360
    Car Build Date:
    03/10/2023 - 13/10/2023
    Concern:
    On Affected Vehicles There Is Concern That The Structural Adhesive Applied To The Bodyshell Has Been Mis-applied.
    Defect:
    On affected vehicles there is concern that the structural adhesive applied to the bodyshell has been mis-applied.
    Remedy:
    Install two rivets and seal with approved sealant.
  • Announcement date:
    06/12/2023
    Recalls number:
    R/2023/338
    Car Build Date:
    04/09/2023 - 20/10/2023
    Concern:
    On Affected Range Rover Vehicles Fitted With V8 Gasoline Nc11 Engines The Fixings Used To Secure The Engine Mounted Oil Cooler Hoses Have Been Found To Have Inadequate Thread Engagement.
    Defect:
    On affected Range Rover vehicles fitted with V8 Gasoline NC11 engines the fixings used to secure the engine mounted oil cooler hoses have been found to have inadequate thread engagement.
    Remedy:
    Vehicles will have the engine oil cooler pipe fixings inspected and replaced if required.
  • Announcement date:
    24/08/2023
    Recalls number:
    R/2023/244
    Car Build Date:
    06/01/2023 - 08/02/2023
    Concern:
    For Certain Vehicles The Bolt Connecting The Busbar To The Traction Battery Module Connector Has Not Achieved The Required Clamp Force. Arcing At The Joint And Excessive Heat Generation Cannot Be Ruled Out With The Consequence That This May Lead To A Vehicle Fire.
    Defect:
    For certain vehicles the bolt connecting the busbar to the traction battery module connector has not achieved the required clamp force. Arcing at the joint and excessive heat generation cannot be ruled out with the consequence that this may lead to a vehicle fire.�
    Remedy:
    Replacement of the High Voltage battery
  • Announcement date:
    16/08/2023
    Recalls number:
    R/2022/341
    Car Build Date:
    02/11/2015 - 16/03/2016
    Concern:
    On Certain 2014 - 2016 Model Year Land Rover Range Rover Vehicles The Front Suspension Upper Knuckle Joint Could Develop A Crack. In Extreme Cases Where A Crack In The Front Suspension Knuckle Has Developed This May Lead To Detachment Of The Upper Suspension Arm.
    Defect:
    On certain 2014 - 2016 Model Year Land Rover Range Rover vehicles the front suspension upper knuckle joint could develop a crack. In extreme cases where a crack in the front suspension knuckle has developed this may lead to detachment of the upper suspension arm.�
    Remedy:
    Carry out an inspection of the front suspension knuckles and replace parts if required.�
  • Announcement date:
    16/08/2023
    Recalls number:
    R/2022/341
    Car Build Date:
    01/10/2014 - 31/03/2015
    Concern:
    On Certain 2014 - 2016 Model Year Land Rover Range Rover Vehicles The Front Suspension Upper Knuckle Joint Could Develop A Crack. In Extreme Cases Where A Crack In The Front Suspension Knuckle Has Developed This May Lead To Detachment Of The Upper Suspension Arm.
    Defect:
    On certain 2014 - 2016 Model Year Land Rover Range Rover vehicles the front suspension upper knuckle joint could develop a crack. In extreme cases where a crack in the front suspension knuckle has developed this may lead to detachment of the upper suspension arm.�
    Remedy:
    Carry out an inspection of the front suspension knuckles and replace parts if required.�
  • Announcement date:
    13/07/2023
    Recalls number:
    R/2023/163
    Car Build Date:
    23/09/2020 - 29/11/2022
    Concern:
    On Affected 2022 - 2023 Model Year Land Rover Range Rover Vehicles The External Rear Lamp Mounted In The Body Could Partially Or Permanently Fail To Operate Resulting In One Or More Of The Light Sources Not Working.
    Defect:
    On affected 2022 - 2023 Model Year Land Rover Range Rover vehicles the external rear lamp mounted in the body could partially or permanently fail to operate resulting in one or more of the light sources not working.
    Remedy:
    Affected vehicles will have the foam block mounted in the bodyshell removed. The rear lamp mounted in the body and rear tail lamp link lead wiring will be checked for their condition. Where the lamp and wiring are qualified OK no further remedy is required. Where the lamp or wiring are qualified Not OK the lamp will be replaced.
  • Announcement date:
    05/06/2023
    Recalls number:
    R/2023/097
    Car Build Date:
    08/12/2021 - 06/07/2022
    Concern:
    On Affected Vehicles The Second Row 60% Seat Frame May Have A Latch Installed With A Defective Weld. In Vehicles That Have A Defective Weld On The Second Row 60% Seat Frame Latch The Seat May Not Be Correctly Secured.
    Defect:
    On affected vehicles the second row 60% seat frame may have a latch installed with a defective weld. In vehicles that have a defective weld on the second row 60% seat frame latch the seat may not be correctly secured.
    Remedy:
    The rear seat base latch will be inspected. Where the inspection reveals a not OK condition the rear seat 60% frame and associated components will be replaced.
  • Announcement date:
    18/05/2023
    Recalls number:
    R/2023/044
    Car Build Date:
    24/08/2022 - 09/01/2023
    Concern:
    For Certain 2023 Model Year 3.0l Aj20-p6 Land Rover Range Rover Range Rover Sport Range Rover Velar Discovery And Defender Vehicles A Small Number Of Engines The Cam Carrier Oil Gallery Hasn T Been Fully Drilled. As A Result The Oil Channel Could Be Blocked Leading To Accumulation Of Oil Against The Pressure Control Valve Rubber Membrane And Subsequently An External Oil Leak Or Increased Oil Carryover Into The Air Intake System.
    Defect:
    For certain 2023 Model Year 3.0L AJ20-P6 Land Rover Range Rover Range Rover Sport Range Rover Velar Discovery and Defender vehicles a small number of engines the cam carrier oil gallery hasn�t been fully drilled. As a result the oil channel could be blocked leading to accumulation of oil against the pressure control valve rubber membrane and subsequently an external oil leak or increased oil carryover into the air intake system.
    Remedy:
    The engine cam carrier will be inspected and where an incorrectly machined cam carrier is found replace it with a correctly machined component. Depending on mileage and engine conditions further associated components may require replacement.
  • Announcement date:
    09/05/2023
    Recalls number:
    R/2023/087
    Car Build Date:
    06/04/2017 - 10/12/2021
    Concern:
    On Affected Vehicles There Is A Risk Where The Water Pump Pully Drive Belt Can Become Damaged Leading To Detachment Or Destruction. Where Water Pump Pully Drive Is Lost This Leads To A Loss Coolant Flow In The Engine.
    Defect:
    On affected vehicles there is a risk where the water pump pully drive belt can become damaged leading to detachment or destruction. Where water pump pully drive is lost this leads to a loss coolant flow in the engine.
    Remedy:
    Affected vehicles will have the engine coolant elbow replaced. In addition a turbocharger feed coolant pipe will be replaced.
  • Announcement date:
    12/09/2022
    Recalls number:
    R/2022/262
    Car Build Date:
    25/09/2020 - 07/06/2022
    Concern:
    Some Of The Hot End Exhaust Bracket Fixings May Not Have Been Fastened Or Not Have Been Fastened To The Correct Torque
    Defect:
    Some of the hot end exhaust bracket fixings may not have been fastened or not have been fastened to the required torque.
    Remedy:
    Check for the presence of the exhaust bracket fixings and where necessary install new fixings or tighten existing fixings to the specified torque.
  • Announcement date:
    20/05/2022
    Recalls number:
    R/2022/139
    VIN start:
    SALKABAW1NA000555
    VIN end:
    SALKA9BW1NA006914
    Car Build Date:
    29/11/2021 - 31/03/2022
    Concern:
    The Front Crash Sensor Fixings May Not Have Been Installed To The Specified Torque
    Defect:
    The front crash sensor fixings may not have been installed to the specified level of torque.
    Remedy:
    Check and tighten the front crash sensor fixing to the specified level of torque.
  • Announcement date:
    04/12/2020
    Recalls number:
    R/2020/293
    VIN start:
    SALGA2AW5MA416001
    VIN end:
    SALGA2BW0MA420049
    Car Build Date:
    27/08/2020 - 29/09/2020
    Concern:
    Exhaust Gas Recirculation Crossover Pipe May Not Be To Specification
    Defect:
    The Exhaust Gas Recirculation (EGR) crossover pipe may have been manufactured away from specification.
    Remedy:
    Check and repair the vehicle with a part manufactured to the correct specification.
  • Announcement date:
    09/04/2019
    Recalls number:
    R/2019/112
    VIN start:
    SALGS5RE6KA550751
    VIN end:
    SALGA3BK8KA551293
    Car Build Date:
    15/02/2019 - 20/02/2019
    Concern:
    The Routing Of The Electrical Harness Has Insufficient Clearance To The Metalwork Within The Steering Column Assembly
    Defect:
    The routing of the electrical harness within the steering column assembly has insufficient clearance.
    Remedy:
    Inspect the steering column electrical harness apply further protective material and repair damaged wiring where required.
  • Announcement date:
    31/01/2019
    Recalls number:
    R/2019/015
    VIN start:
    SALGA2BJ2JA380220
    VIN end:
    SALGA2BJ1KA541710
    Car Build Date:
    10/11/2017 - 18/12/2018
    Concern:
    The Directional Indicators Fail To Operate When The Steering Column Mounted Control Stalks Are Used
    Defect:
    The directional indicators may fail to operate.
    Remedy:
    Update the vehicle with the latest software on affected vehicles.
  • Announcement date:
    31/01/2019
    Recalls number:
    R/2019/013
    VIN start:
    SALGS2SV7KA531120
    VIN end:
    SALGA2BV4KA542269
    Car Build Date:
    10/10/2018 - 19/12/2018
    Concern:
    Crankshaft Pulley Retaining Bolt May Fracture
    Defect:
    The crankshaft pulley retaining bolt may fracture due to a production specification error.
    Remedy:
    Replace the crankshaft pulley centre retaining bolt with one that has been manufactured to the correct specification.
  • Announcement date:
    25/09/2018
    Recalls number:
    R/2018/243
    VIN start:
    SALGA2BJ8JA380416
    VIN end:
    SALGA2BJ3JA504964
    Car Build Date:
    13/11/2017 - 17/03/2018
    Concern:
    Autonomous Emergency Braking Feature Will Not Be Available
    Defect:
    Autonomous Emergency Braking (AEB) feature will not be available.
    Remedy:
    On affected vehicles download the latest software to the vehicle.
  • Announcement date:
    25/06/2018
    Recalls number:
    R/2018/160
    VIN start:
    SALGA2BY9JA348961
    VIN end:
    SALGA2AY3JA510665
    Car Build Date:
    28/03/2017 - 25/05/2018
    Concern:
    Fuel Gauge Displays An Inaccurate Reading
    Defect:
    On certain 2018 and 2019 Model Year Land Rover Range Rover and Range Rover Sport PHEV vehicles where the indicated fuel level on the fuel gauge shows approximately 30% the fuel tank is empty resulting in an engine stall. The vehicle will enter into reduced performance mode and if the customer continues to drive the vehicle will continue to run for circa 8 miles/13Km. The vehicle engine will then cut out without warning. If the traction battery charge status is at least 10% or greater the electric motor will take up drive until such time as traction battery power is depleted. Where the traction battery charge status is below 10% drive from the electric motor is not possible and the vehicle will cut out whilst in motion. All 12 volt powered electrical functions such as power assisted steering exterior lighting and brake assistance will continue to operate as designed. Engine cut out with minimal warning to the driver may lead to an increased risk of an accident.
    Remedy:
    Fit a new revised fuel level sensor float to the vehicle.
  • Announcement date:
    13/03/2018
    Recalls number:
    R/2018/036
    VIN start:
    SALGA3BY1JA343646
    VIN end:
    SALGA2AY5JA387693
    Car Build Date:
    05/05/2016 - 31/01/2018
    Concern:
    Fuel May Leak
    Defect:
    The brazing of the fuel rail end caps is inconsistent and may not correctly seal the fuel rail ends. Fuel vapour and liquid fuel leaks can occur over time. This can lead to a liquid fuel leak into the engine bay.
    Remedy:
    On affected vehicles replace the fuel rail with a correctly manufactured version.
  • Announcement date:
    24/11/2017
    Recalls number:
    R/2017/288
    VIN start:
    SALGA2EV6HA311572
    VIN end:
    SALGW2FE4HA366599
    Car Build Date:
    04/09/2016 - 17/08/2017
    Concern:
    Instrument Cluster May Intermittently Go Blank
    Defect:
    Due to a software issue the Instrument cluster may intermittently go blank.
    Remedy:
    Affected vehicles will be recalled to have the latest software installed/downloaded.
  • Announcement date:
    02/05/2017
    Recalls number:
    R/2017/138
    VIN start:
    SALGA2KE1GA290617
    VIN end:
    SALGA2EK2HA320551
    Car Build Date:
    12/04/2016 - 31/10/2016
    Concern:
    Passengr Seat Belt Locking Retractor May Not Function Correctly
    Defect:
    The Emergency Locking Retractor in the front passenger safety belt assembly may not function correctly. The Emergency Locking Retractors are equipped with a vehicle-sensitive locking mechanism and a webbing-sensitive locking mechanism. The vehicle-sensitive locking mechanism may not lock as designed. In the event of a pre-crash brake event where the passenger airbag deploys front passenger seat forward facing child seat occupants may sustain more severe injuries.
    Remedy:
    Recall the vehicles that are likely to be affected and replace the left hand front seat belt assembly.
  • Announcement date:
    01/05/2017
    Recalls number:
    R/2017/103
    VIN start:
    SALGS2PFXGA314542
    VIN end:
    SALGA2KF0GA320134
    Car Build Date:
    20/09/2016 - 25/10/2016
    Concern:
    Front Passenger Airbag May Not Deploy
    Defect:
    The front passenger airbag may not function properly due to a deviation in generant mix ratio. In the event of a crash of sufficient severity the front passenger airbag may not deploy when required. Failure to deploy can lead to increased injuries to the passenger seat occupant.
    Remedy:
    Recall the vehicles that are likely to be affected and replace the front passenger airbag.
  • Announcement date:
    31/12/2016
    Recalls number:
    R/2016/303
    VIN start:
    SALGS2EF7GA304537
    VIN end:
    SALGS2FK1HA320598
    Car Build Date:
    12/07/2016 - 26/10/2016
    Concern:
    Seat Belt Pretensioner May Not Deploy
    Defect:
    It has been identified by the seat belt Pre-Tensioner manufacturer that the pre-tensioner initiator generant mix ratio does not meet specification. This can therefore result in the initiator not functioning correctly which can lead to none activation of the pre-tensioner.
    Remedy:
    Recall all affected vehicles to check the pre-tentioner and if required replace it with a new quality assured component.
  • Announcement date:
    31/12/2016
    Recalls number:
    R/2016/307
    VIN start:
    SALGS2PF6GA310620
    VIN end:
    SALGS2PF4GA318022
    Car Build Date:
    12/07/2016 - 26/10/2016
    Concern:
    Front Passenger Airbag May Not Deploy
    Defect:
    It has been identified by the air-bag manufacturer that the air-bag initiator generant mix ratio does not meet specification. This can therefore result in the initiator not functioning correctly which can lead to non-deployment of the air-bag. Should a collision occur then there is an increased risk of injury to the passenger.
    Remedy:
    Recall all affected vehicles to replace the air-bag with a new quality assured component.
  • Announcement date:
    23/06/2016
    Recalls number:
    R/2016/098
    VIN start:
    SALGA2KE6DA000013
    VIN end:
    SALGA2HF4DA124233
    Car Build Date:
    02/04/2012 - 02/05/2013
    Concern:
    Engine May Cut Out
    Defect:
    An incorrectly manufactured crank position sensor may cause the engine to unexpectedly cut out or not to start.
    Remedy:
    On recalled vehicles the engine serial number will be checked and if within the affected range the crank position sensor will be replaced.
  • Announcement date:
    01/11/2015
    Recalls number:
    R/2015/187
    VIN start:
    SALGA2VF2FA239176
    VIN end:
    SALGA2VF0FA241024
    Car Build Date:
    01/06/2015 - 12/06/2015
    Concern:
    Rear Passenger Seatbelt May Fail In A Collision
    Defect:
    The second row seat backrest on vehicles with the manual recline second row seat system may not latch robustly in position. It is possible the seat belt may not correctly restrain the occupant in the event of a collision.
    Remedy:
    On affected vehicles inspect the second row seat mechanism and if necessary fit the correct specification components.
  • Announcement date:
    04/08/2015
    Recalls number:
    R/2015/119
    VIN start:
    SALGA2KEXDA000001
    VIN end:
    SALGA2DF2FA223058
    Car Build Date:
    29/03/2012 - 23/05/2015
    Concern:
    Vehicle Door(s) May Open When Car Is In Motion
    Defect:
    The door could be unlatched when in the closed position and no indication provided of an unlatched condition. Vehicle doors not latched in either the primary of secondary state may during driving open. This can increase the risk of a vehicle crash and/or compromise the safety of vehicle occupants and other road users.
    Remedy:
    Recall the vehicles that are likely to be affected and download the latest level of software. A limited number of vehicles may also require a Remote Function Actuator module to be fitted.
  • Announcement date:
    13/04/2015
    Recalls number:
    R/2015/036
    VIN start:
    SALGA2VF7FA211955
    VIN end:
    SALGA2EF3FA215386
    Car Build Date:
    06/01/2015 - 23/01/2015
    Concern:
    Wheel Nuts May Detach
    Defect:
    On affected vehicles the road wheel nuts may not have been manufactured to the correct specification. These wheel nuts may crack when subject to shock loads and detach from the stud. This may lead to insecurity and possible detachment of a road wheel.
    Remedy:
    Recall affected vehicles and replace wheel nuts. Locking wheel nuts are not affected.
  • Announcement date:
    10/04/2015
    Recalls number:
    R/2015/038
    VIN start:
    SALGA2EE3FA197043
    VIN end:
    SALGA2KEXFA216496
    Car Build Date:
    14/10/2014 - 02/02/2015
    Concern:
    Fire May Occur
    Defect:
    The ground wiring for the air conditioning blower within the cockpit harness may not be to specification. This can lead to the wire getting hot and melting the plastic insulation and associated burning smell. If ignored and the loom gets significantly damaged there is a possibility of fire.
    Remedy:
    Recall the vehicles that are likely to be affected and replace the earth wire. Where other wiring/insulation is affected necessary repairs will be carried out using the correct repair procedures.
  • Announcement date:
    17/02/2015
    Recalls number:
    R/2015/013
    VIN start:
    SALGA2EEXDA100000
    VIN end:
    SALGA2DF7EA154799
    Car Build Date:
    16/08/2012 - 08/01/2014
    Concern:
    Possible Loss Of Braking Efficiency
    Defect:
    On affected vehicles the servo vacuum hose may have been incorrectly routed and can chafe against the auxiliary drive pulley. This can lead to failure of the hose and a loss of brake servo assistance.
    Remedy:
    On affected vehicles check brake servo hose. If in good condition correctly reroute and secure hose. If hose is damaged replace hose and correctly route and secure.
  • Announcement date:
    23/01/2015
    Recalls number:
    R/2015/014
    VIN start:
    SALLMAM546A198146
    VIN end:
    SALLMAMJ3CA393639
    Car Build Date:
    14/03/2005 - 26/07/2012
    Concern:
    Possible Loss Of Braking Efficiency
    Defect:
    It is possible that one or both of the front brake hoses could rupture allowing brake fluid to leak. A warning lamp and message will appear on the dash board when the fluid depletes to a certain level. Braking capability will be retained by the rear brake circuit pedal feel will be degraded and pedal travel extended. Stopping distances will increase.
    Remedy:
    Recall the vehicles that are likely to be affected and replace both front brake hoses.
  • Announcement date:
    10/11/2014
    Recalls number:
    R/2014/091
    VIN start:
    SALGA2KEXDA000001
    VIN end:
    SALGA2JE9DA110085
    Car Build Date:
    09/03/2012 - 22/01/2013
    Concern:
    Risk Of Fire
    Defect:
    An internal fault can create a short circuit within the fan control module which may lead to overheating of the insulation and ultimately fire within the engine bay. This may happen with the engine switched off and possibly when the vehicle is unattended..
    Remedy:
    Replace electric cooling fan assembly on affected vehicles
  • Announcement date:
    02/05/2014
    Recalls number:
    R/2014/040
    VIN start:
    SALVA2BG4EHLV856654
    VIN end:
    SALVA2AE7EHLV880754
    Car Build Date:
    02/11/2013 - 10/01/2014
    Concern:
    Vehicle May Become Unstable
    Defect:
    The right hand rear suspension link arm to knuckle fixings may not be to specification. When subjected to normal use loading one or both of the fixings may fracture. Where one or both of the suspension link arm fixings fracture vehicle stability may be compromised.
    Remedy:
    Recall the vehicles that are likely to be affected and replace both the right hand side rear suspension link arm to knuckle fixings and torque to the correct specification.
  • Announcement date:
    04/04/2014
    Recalls number:
    R/2014/039
    VIN start:
    SALGV2EF0EA124983
    VIN end:
    SALGS2WF8EA142560
    Car Build Date:
    07/05/2013 - 10/10/2013
    Concern:
    Front Direction Lamp Indicator Warning Light May Fail
    Defect:
    In the event of a front direction indictor lamp failure the audible and visual warning (double click/double flash warning) will not function thereby not informing the driver of the failure. This can result in the vehicle not being rectified for a prolonged period which increases the chance of a collision with other road users.
    Remedy:
    Recall the vehicles that are likely to be affected and update the vehicle with the latest software.
  • Announcement date:
    27/08/2013
    Recalls number:
    R/2013/091
    VIN start:
    SALVA2BE7CH641555
    VIN end:
    SALVB2CC8DH850315
    Car Build Date:
    01/01/2012 - 31/10/2013
    Concern:
    Fire May Occur
    Defect:
    It is possible that a leak can occur between the injector spill rail connection and the plastic fuel return pipe. This can cause leakage of fuel which can either pool on the engine cylinder head and then become deposited onto the road surface where it could cause a skid risk to other motorist or if the fuel comes into contact with extremely hot engine components an exhaust manifold for instance it is possible that an under bonnet fire could ensue.
    Remedy:
    Recall all affected vehicles inspect the fuel spill rail/return pipe and if required replace the spill rail with a new modified rail.
  • Announcement date:
    18/12/2012
    Recalls number:
    R/2012/153
    VIN start:
    SALVA2AE7CH687968
    VIN end:
    SALVA2BG1CH688422
    Car Build Date:
    11/06/2012 - 11/06/2012
    Concern:
    Brakes May Fail
    Defect:
    Mounting bolts for the rear brake caliper may not be torqued to the correct specification. This will create noise from the rear of the vehicle whilst it is being driven and during braking and should warn the driver of the issue. However if the vehicle continues to be driven it is possible the bolts can work loose thus allowing the brake caliper to detach. This will result in the caliper contacting the road wheel which can cause brake failure or sudden deflation of the tyre with subsequent loss of control of the vehicle.
    Remedy:
    Recall affected vehicles to check the mounting bolts and re-torque them.
  • Announcement date:
    11/12/2012
    Recalls number:
    R/2012/154
    VIN start:
    SALVA2BG0CH704223
    VIN end:
    SALVA2AE6DH713526
    Car Build Date:
    20/08/2012 - 18/09/2012
    Concern:
    Steering May Fail
    Defect:
    The steering rack mounting bolts may not be fully tight. If the steering gear fixings are below the required torque the driver will experience abnormal noise and feedback through the steering wheel during low speed manoeuvring and at higher speeds some easily corrected minor over steer. If the driver ignores the warning signs both fixings could become sufficiently loose to detach from the vehicle making directional control of the vehicle difficult.
    Remedy:
    Recall the vehicles that are likely to be affected to inspect the steering gear and check the steering gear mounting fixings are tightened to the correct torque.
  • Announcement date:
    10/12/2012
    Recalls number:
    R/2012/116
    VIN start:
    SALLMAMD4CA370800
    VIN end:
    SALLMAME4CA370892
    Car Build Date:
    24/11/2011 - 24/11/2011
    Concern:
    Windscreen May Not Be Secure
    Defect:
    The affected vehicles windshield may not be fully bonded in to the aperture. Where the windshield is not bonded water ingress might occur and there may be reports of increased wind noise. Furthermore this concern may also be a non-compliance with the regulatory requirements of FMVSS 212 or FMVSS 216 Windshield Mounting.
    Remedy:
    Approved Service Centre will remove and replace the windscreen with the correct bonding agent in line with existing service repair procedures.
  • Announcement date:
    03/12/2010
    Recalls number:
    R/2010/147
    VIN start:
    SALLSAA147A983192
    VIN end:
    SALLSAA649A215295
    Car Build Date:
    01/09/2006 - 30/06/2009
    Concern:
    Fire May Occur
    Defect:
    The front pump bearing on some aftermarket replacement High Pressure Fuel Pumps may fail due to lack of sufficient lubrication. This will cause failure of the shaft seal which will cause a fuel leak and if not rectified could cause a vehicle fire.
    Remedy:
    Recall affected vehicles and replace fuel pump with the latest specification pump.
  • Announcement date:
    05/08/2009
    Recalls number:
    R/2009/069
    VIN start:
    SALLMAM249A305421
    VIN end:
    SALLMAM549A306546
    Car Build Date:
    01/04/2009 - 31/05/2009
    Concern:
    Full Windscreen Retention May Not Be Achieved In The Event Of An Air-bag Deployment
    Defect:
    The windscreen bonding process to vehicle may not be effective. Water and wind ingress may occur. In extreme cases in an air bag deployment or collision the windscreen may detach.
    Remedy:
    Recall affected vehicles to check for presence of primer/activator on REAR tailgate glass. If present no further action is required as all screen security is assured. If not present the FRONT windscreen will be removed and re-fitted in-line with exiting service repair procedures.
  • Announcement date:
    01/01/2007
    Recalls number:
    R/2006/218
    VIN start:
    SALLMAMA42A100085
    VIN end:
    SALLMAM546A212895
    Car Build Date:
    04/07/2002 - 03/10/2006
    Concern:
    Brake Fluid May Leak From Brake Pipe
    Defect:
    Brake fluid may leak from either the right hand front or left hand front brake caliper bridge pipe
    Remedy:
    Recall affected vehicles and replace the caliper bridge pipe on all four calipers with a revised corrosion resistant part.
  • Announcement date:
    30/11/2005
    Recalls number:
    R/2005/156
    VIN start:
    SALLMAM336A212296
    VIN end:
    SALLMAM536A212008
    Car Build Date:
    16/08/2005 - 15/09/2005
    Concern:
    The Parking Function Of The Automatic Transmission May Not Operate Correctly
    Defect:
    Due to the presence of an out of specification component within the automatic gearbox parking brake interlock system. The parking function may not fully engage when the operating lever is moved to park despite all indicators showing that park has been achieved. If the parking brake is not applied the vehicle may roll away.
    Remedy:
    Recalled vehicles will have the out of specification component replaced with a quality assured item.
  • Announcement date:
    05/05/2005
    Recalls number:
    R/2004/069
    VIN start:
    SALLHAMM3KA637653
    VIN end:
    SALLHAMM3MA664120
    Car Build Date:
    19/04/1993 - 19/02/1996
    Concern:
    Possibility Of Stress Cracks In The Plastic Fuel Tank
    Defect:
    Due to a material specification change combined with inadequate tool design and process control it is possible that stress cracking can occur at either the fuel tank vent valve ring welding the breather pipe weld or the filler pipe stub.
    Remedy:
    Replace the fuel tank with an improved design.
  • Announcement date:
    07/03/2005
    Recalls number:
    R/2005/008
    Car Build Date:
    24/08/2004 - 15/11/2004
    Concern:
    Tv Screen May Not Switch Off Whilst The Vehicle Is In Motion
    Defect:
    It has been identified that the TV will be viewable by the driver whilst the vehicle is in motion if the TV is being operated in the full screen position when the vehicle is stationary and a call through the in car phone system is either made or received and not ended prior to the vehicle being set in motion.
    Remedy:
    Recalled vehicles will have the high level front display unit reprogrammed with a revised level of software thus ensuring that the TV screen is switched off whilst the vehicle is in motion.
  • Announcement date:
    07/12/2004
    Recalls number:
    R/2004/193
    VIN start:
    SALLMAMA44A176708
    VIN end:
    SALLMAMA34A177695
    Car Build Date:
    22/06/2004 - 09/07/2004
    Concern:
    Yaw Rate Sensor May Suffer Internal Delamination
    Defect:
    On certain vehicles equipped with a dynamic stability control the yaw rate sensor may have suffered internal delamination. This could result in actuation of the stability control incorrectly resulting in uneven and unexpected application of the brakes.
    Remedy:
    Recalled vehicles will be inspected in order to ascertain whether they contain a suspect sensor. Should this indeed be the case the sensor will be replaced with a quality assured part.
  • Announcement date:
    14/03/2002
    Recalls number:
    R/2002/035
    VIN start:
    2A100042 to 2A104082
    Car Build Date:
    01/12/2001 - 31/03/2002
    Concern:
    Risk Of Fire
    Defect:
    There is a possibility that a short circuit may occur in the cigar lighter bulb holder when the vehicle lighting system is operated.
    Remedy:
    Disconnect the illumination feed to the lighter and remove the bulb.
  • Announcement date:
    05/12/2000
    Recalls number:
    R/2000/074
    VIN start:
    LP300000 - LP418689
    Car Build Date:
    01/01/1994 - 31/12/1999
    Concern:
    Cooling System Leaks
    Defect:
    There is a possibility of premature failure of the cooling system hoses and throttle body heater gasket. Expelled coolant allowed to remain on hot engine components can result in the evaporation of the water content and leave an artificially high concentration level of anti - freeze which is in extreme circumstances both corrosive and inflammable.
    Remedy:
    Recall affected vehicles to replace cooling system hoses / throttle body heater gasket with quality assured parts.
  • Announcement date:
    20/03/1998
    Recalls number:
    R/1998/003
    VIN start:
    LJ500000 to LJ557881
    Car Build Date:
    01/01/1994 - 31/03/1997
    Concern:
    Involuntary Operation Of Air Bag
    Defect:
    Involuntary operation of the air bag may occur as a result of an intermittent electrical fault.
    Remedy:
    Recall the affected vehicles for the fitment of a safety fuse link in the air bag circuit.
  • Announcement date:
    29/03/1996
    Recalls number:
    R/1996/032
    VIN start:
    LP300000 to LP309758
    Car Build Date:
    01/06/1994 - 31/03/1995
    Concern:
    Cracking Of Rear Suspension Composite Links
    Defect:
    The rear suspension composite links are below specification and may develop small stress cracks at the aluminium eye end. Failure of the link(s) would affect the security of the rear axle.
    Remedy:
    Recall the affected vehicles for replacement of the suspension links with quality assured examples.
  • Announcement date:
    02/07/1993
    Recalls number:
    R/1993/032
    VIN start:
    Various
    Car Build Date:
    10/08/1992 - 15/09/1992
    Concern:
    Possible Malfunction Of Electric Window Switch
    Defect:
    The window operating switch may latch in the 'pressed' condition. This could result in the window continuing to operate up or down when pressure on the switch is released.
    Remedy:
    Recall the affected vehicles for replacement of the original window switches with quality assured units.
Step 3 - Contact your nearest dealer

Enter your postcode to see your nearest franchised dealer: